|
KiCADKicad
|
|
|
OpenSCADOpenSCAD
|
FluxEngine Hat
Adapter PCB and snap cover for FluxEngine
Provides both a 34-pin connector for normal 3.5 inch and 5.25 inch drives, and a 50-pin connector for 8 inch drives.
The fpga board may be connected with or without soldering pins or sockets.
The 26-pin rows act as friction-fit connectors that work like sockets without needing to actually install sockets.
You can still solder normally to connect the fpga board permanently, or solder normal sockets.
To use the solderless option:
- Order the hat pcb with ENIG finish to make the holes gold plated.
- Solder the 34 & 50-pin connectors and the jumper pins, but leave the two outside 26-pin rows clean.
- Solder the two 26-pin male pin headers and the 5-pin female socket to the bottom of the fpga board.
Now the fpga board may be attached by just pushing the pins into the staggered rows,
and also removed again any time to use with a different hat, for some other project on a breadboard,
and re-attached again at any time to use for FluxEngine again.
This FluxEngine_Hat supports Shugart-compatible 8-inch drives, which is most 8-inch drives.
On the github repo there are other hats that support CDC drives. (Control Data Corporation / Magnetic Peripherals Inc)
Some CDC drives are Shugart-compatible, but others have other pinouts that are not Shugart compatible.
FluxEngine Hat
*PCBWay community is a shared platform and we are not responsible for any design issues.
- Comments(0)
- Likes(0)
- 0 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
More by Brian K. White
- LPT Capture Capture the output from a parallel printer port.This is a rendition of https://www-user.tu-chemnitz....
- FluxEngine Hat Adapter PCB and snap cover for FluxEngineProvides both a 34-pin connector for normal 3.5 inch and 5....
- MiniNDP - mini Node DataPac Re-implementation of Node Systems DATAPAC.256k ram disk for TRS-80 Model 100, TANDY Model 102, TANDY...
- Batteries for REXCPM Provides an on-board memory battery for the REXCPMAssembly notes:For battery holders BT1, BT2, BT3 (...
- 512k MRAM IC-Card for TANDY WP-2 REQUIRES 1.2 mm PCBWarning: The total cost for parts for this is around $100 USDThis is an "IC-Card"...
- M4ROM_TANDY - Writable multi option rom module for TRS-80 Model 100/102/200 ONLY for TRS-80 / TANDY Models 100, 102, 200Provides 4 virtual 32K EPROM from a single 128K flash ch...
- M4ROM Programming Adapter for M4ROM_TANDY and M4ROM_27256 Programming adapter to program M4ROM_TANDY and M4ROM_27256 .Solid electrical contact with the center...
- M4ROM 27256 - Writable multi option rom module for EPSON PX-4, PX-8, TANDY 600, any Molex 78805 socket with standard pinout Provides 4 virtual 32k EPROM from a single 128k flash chip, in a Molex 78802 form factor to fit in a...
- TANDY 600 RAM - TINY Version Tiny version of 96K ram module for TANDY 600The larger card below is the original 96K ram card for c...
- TANDY 600 RAM 96K THT 96K SRAM module for TANDY 600, all through-hole components version. Replaces Tandy Cat. No. 26-3910...
- Teensy MounT https://github.com/bkw777/MounT
- TANDY 600 192K DUAL RAM 192K SRAM for TANDY 600The original option RAM banks for TANDY 600 are 96K, and the machine can acce...
- TANDY 200 RAM 48K TSOP 48K Dual-bank option ram module for TANDY 200How to do the legs: https://gist.github.com/bkw777/52d8...
- reQUAD - RAM Expansion for TRS-80 Model 100 Replaces the internal 32k SRAM in a TRS-80 Model 100 with a software-switchable 4 banks of 32k SRAM ...
- ScopeShuntX Shunt resistor for measuring current with an oscilloscope.Inspired by github.com/voltlog/ScopeShuntS...
- de0-nano fpga rgb2vga https://github.com/bkw777/rgb2vgahttps://sites.google.com/site/tandycocoloco/rgb2vgaConvert 15khz RG...
- DS1000_DIP14 Adapter to replace DIP-14 package 5-tap analog delay line or pin-compatible silicon delay line like ...
- TANDY 600 RAM 96K SRAM module for TANDY Model 600
-
IoT Indoor system with ESP32 to monitor Temperature, Humidity, Pressure, and Air Quality
225 0 0 -
Naruto Multi-color PCB printed with UV technology
106 2 1 -
-
-
-
-