Kube Multisensor - Analog/Digital I/O Expander Submodule
This is a "submodule" board for the Kube v2 multi sensor project (https://www.pcbway.com/project/shareproject/NodeMCU_v_1_2_Board.html). It is a cerrier board to add additional I/O to the Kube "stack", using the MCP23017 chip for 16 channels of digital I/O, and/or the ADS1115 breakout board (thin or wide) from Adafruit for 4 channels of 16-bit analog input.
The MCP23017 chip address pins are broken out, so you can optionally stack up to 8 of these boards for 128 total digital I/O.
The ADS1115 chip address pin is also broken out, and you can address/stack up to 4 of these units, for 16 total analog I/O channels.
All I/O is broken out to terminal blocks, for easy connections.
### TECHNICAL DETAILS / COMPONENTS
BOM:
1 x This board
1 x MCP23017 - https://amzn.to/2S01Otl
1 x ADS1115 - https://amzn.to/2XxGVM4
Jumper Headers - https://amzn.to/2Jvkg9t
Male/Female Headers - https://amzn.to/2EgvnSs
8 x 4-pin 2.54mm pitch screw terminal - https://amzn.to/2XvnzHN
1 x 6-pin Female header - https://amzn.to/2S0L7y8
### LEARN / TOPIC / BUILD INSTRUCTIONS
Watch Livestream video below for prototype build instructions.
Kube Multisensor - Analog/Digital I/O Expander Submodule
*PCBWay community is a shared platform and we are not responsible for any design issues.
- Comments(0)
- Likes(0)
- 0 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
More by BK
- PowerWheels Jeep Bar Light LED carrier board Just fill with 5mm White LEDs (like these - https://amzn.to/3kK4Cu9 - and mount inside the light ass...
- Kube Multisensor - Analog/Digital I/O Expander Submodule This is a "submodule" board for the Kube v2 multi sensor project (https://www.pcbway.com/project/sha...
- Kube Multisensor - Power Supply Module This is a "submodule" board for the Kube v2 multi sensor project (https://www.pcbway.com/project/sha...
- Kube Multisensor - NodeMCU Module Board NodeMCU Breakout Board for DHT, Motion, LED Controller and other sensors (project home at https://ww...
- Kube Multisensor - OLED & Ambimate MS4 Submodule Board ### DESCRIPTIONThis is a "submodule" board for the Kube v2 multi sensor project (https://www.pcbway....
- NodeMCU DHT/Sensor/LED Controller Breakout Board-v.1.1 ### DESCRIPTION(NEW) Version 1.2 of this board is now ready and available here: https://www.pcbway.c...
-
Commodore 1551 Drive Cartridge Replacement
36 0 1 -
RCMHardwareByte-v2.3
47 0 0 -
Terminal Curiosity PCB Ruler
190 0 0 -
(DIY) COMMODORE 64 DEAD-TEST (781220) DIAGNOSTIC CARTRIDGE
278 0 2 -
Creative Micro Designs Inc. CMD FD-2000 / FD-4000 3D Printable Case
347 0 0 -
Creative Micro Designs Inc. CMD FD-2000 / FD-4000 Metal Case
501 0 0 -