|
KiCADKicad
|
|
|
arduino IDEArduino
|
ADS1256 - RP2040 Custom DAQ with GPIOs
This is my (hopefully) last iteration of the ADS1256-based DAQ board. I replaced the ATmega32U4 microcontroller with an RP2040 and made the whole board much more compact so I could fit it in a very specific metal enclosure. The RP2040 is a faster microcontroller, so it will be more reliable to deliver the data quickly or even do some processing onboard. It also has a large flash memory which allows larger code, for example, a more complex signal processing. I picked a fairly large flash (W25Q128JVSIM, 128 Mbit or 16 MB) for this board which is maybe a bit excessive. You can probably use a smaller (W25Q16JVSNIQ (16 Mbit or 2 MB) which is 3 times cheaper, but then don't forget to add a 10k resistor at R2!
Since I had to shrink the board, most of the GPIO pins are not available. However, the purpose of the circuit is to send the acquired data from the ADS1256 AD converter to the computer via USB, so there's no need for extra pins anyway. Even the enclosure I picked prohibits having more than the USB and the input pins of the ADS1256 available.
2024-05-19 UPDATE: Apparently, some people would like to access multiple GPIO pins. So I redesigned the board a bit and made it possible to access all of the GPIO pins, except the pins used for the ADS1256. I even designed a front panel (see the GPIO version) to make it easier to access all the pins. However, if you don't need any of the GPIO pins, you can go with the normal version of the front panel. Furthermore, if you don't need the GPIOs, you can neglect J11 and J12 connectors on the bottom of the PCB.
The library I published on my GitHub is perfectly compatible with the board. One just has to make sure that the SPI pins are the 2-3-4 (SCK, MOSI, MISO) pins. This is automatically the case when the code is compiled for the "Waveshare RP2040 Zero" version of the RP2040 microcontroller. But I discuss all the details in my video anyway:
If you want to get the exact same enclosure, check the link below. I designed PCB-based front and rear panels for the enclosure as well.
ADS1256 - RP2040 Custom DAQ with GPIOs
*PCBWay community is a shared platform and we are not responsible for any design issues.
- Comments(0)
- Likes(0)
- 0 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
More by Curious Scientist
- 10th Anniversary Badge I designed this small badge for PCBWay's 10th anniversary. I tried to make a deeper meaning to the b...
- ADS1256 - Atmega32u4 Custom DAQ board IntroductionIn this project, I show you two things. One is a new version (v1.2) of my custom DAQ bas...
- Debounced rotary encoder module In this project, I show you my approach to making a rotary encoder module.One can buy different rota...
- Custom ADS1256 board with ATmega32U4 I created my own ADS1256 PCB after working with this AD converter for several years. I wanted to bui...
- ADS1256 - RP2040 Custom DAQ with GPIOs This is my (hopefully) last iteration of the ADS1256-based DAQ board. I replaced the ATmega32U4 micr...
- High-performance 3-axis stepper motor control panel In this project, I show you my new development which is a high-performance 3-axis stepper motor cont...
- STM32F070F6P6 miniature USB microcontroller board A small but powerful Arduino-compatible STM32 board.I designed this board because I was curious if i...
- Stepper motor developing platform IntroductionIn this project, I show you my newest device which is a stepper motor developing platfor...
- Custom-made self-contained DC power meter This project realizes a tiny "self-sufficient" power meter that can be inserted into any DC power li...
- 10-channel NTC thermistor-based temperature logger This project is designed to be a 10-channel temperature logger based on 10k NTC thermistors.I design...
- Educational board for strain gauges, Wheatstone bridges and op-amps I show you a little device that I built so I can explain more things related to strain gauges, Wheat...
- Focus Stacking Mechanism In my previous project, I shared the PCB for this mechanism. In this project, I share the parts of t...
- Focus Stacking Circuit For Macro Photography This circuit is mainly designed to serve as a tool for shooting pictures for focus stacking macro ph...
- Self-contained PCB weighing scale Note! Please follow the attached interactive BOM. It will help you to find the correct components an...
- Weighing scale made of a PCB In this project, I wanted to try something new and fun.First, I wanted to know if I can use the trac...
- TCD1304 miniature PCB In this project, I continued working with the TCD1304 linear CCD. I created this PCB to fit on the b...
- Reflow hot plate controller board Description:This project realizes a custom made reflow hot plate controller. I made a fancy graphica...
- A custom ATmega32u4 board I decided to make my own ATmega32u4-based microcontroller board for several reasons. I wanted to hav...
-
Creative Micro Designs Inc. CMD FD-2000 / FD-4000 3D Printable Case
93 0 0 -
Creative Micro Designs Inc. CMD FD-2000 / FD-4000 Metal Case
115 0 0 -
-
-
IoT Indoor system with ESP32 to monitor Temperature, Humidity, Pressure, and Air Quality
675 0 3 -
Naruto Multi-color PCB printed with UV technology
232 2 1 -
-